Reset Canon MP145

*error E5

Step 1 : Push Power switch by continue (Tekan Power On/Off)
Step 2 : inserrt plug(Masukan Power, Power Tetap di Tekan)
step 3 : Tekan Tombol Reset 1x, lepaskan Tombol Pwr, Tekan Reset dua kali lagi Sampai Menjadi 0 (tekan tombol tanpa jeda)
Step 4 : Push + display change from 0 to 1 (tekan tombol + untuk merubah 0 ke 1)
Step 5 : Push Power switch again , Printer will be print 1 page(tekan tombol power –> tombol start sampai ngeprint 1 hal.)
step 6 : Open cover (buka tutup printer)
Step 7 : Unplug (cabut kabel power)
Step 8 : Take out ink 40 and 41(lepaskan catridge 40 dan 41)
Step 9 : Insert plug again (pasang kabel power)
Step 10 : Push power switch (tekan tombol power)
Step 11 : Open cover (scan cover) (buka tutup scaner)
Step 12 : Inksert ink 40 , 41 again (masukan catridge 40 dan 41)


berikut ini resep ngereset waste ink counter (error E16) :

1. Matikan printer (kabel power masih tercolok), tekan dan tahan tombol STOP/RESET kemudian tekan tombol ON/OFF
2. Tahan tombol ON/OFF, tekan tombol STOP/RESET 2x
3. Lepaskan kedua tombol dan printer akan masuk ke SERVICE MODE
4. Printer akan charging
5. Setelah printer selesai charging, tekan tombol STOP/RESET 4x. (Waste ink counter reset)
6. Setiap kali tombol STOP/RESET ditekan, lampu ON/OFF akan berubah warna hijau dan oranye
7. Matikan printer dan cabut kabel POWER
8. Hidupkan kembali printer.

The number of the Reset :
button pressing
LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset
5) Unplug cable power. (for MP145 / MP150)
6) Turn Off Power. (for MP160)

Error Code/Kode Error :
E2-2 = No paper (ASF)
E3-3 = Paper jam
E4 = No ink
E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly
E8 = Waste ink absorber full, or platen waste ink absorber full
E9 = The connected digital camera / video camera does not support Camera Direct Printing
E14 = The Ink cartridges whose destination are wrong
E15 = Ink cartridge is not installed E16 – Ink remaining is unknown
E16 -E19 = Failed to scan head alignment sheet
E22 = Carriage error
E23 = Paper feed error
E24 = Purge unit error
E25 = ASF(cam) sensor error
E26 = Internal temperature rise error
E27 = Waste ink absorber full or platen waste ink absorber full
E28 = Ink cartridge temperature rise error -
E29 = EEPROM error
E33 = Paper feed position error
E35 15 = USB Host VBUD overcurrent error – USB
E37 17 = Abnormal motor driver error
E40 20 = Other hardware error
E42 22 = Scanner error


E27 = Waste ink absorber full or platen waste ink absorber full

Procedure to reset Printer canon MP145 and Canon MP160 with Error Code Message for Printer Canon MP145 and Canon MP160, you can find error code message the end of this post:

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop/ Reset button.
2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
4) When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in orange and green, starting with orange.)note: press 4 times for waste ink counter reset.

The number of the Reset
button pressing
LED Function Remarks
0 time Green Power off

1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset

5) Unplug cable power. (for MP145 / MP150)

软件证书过期的解决办法

软件证书过期的解决办法

总有人反映下载安装S60v3软件时提示证书过期无法安装，其实这个根本算不上是问题，
出现这种问题是因为你安装这个软件时的日期已经超过软件作者修改、创建软件时证书的有效期.

解决方法很简单，只要将手机时间调到作者创建软件时所用证书的有效期内即可正常安装.
具体方法:
1,在安装时,选择查看证书详细,其中有证书到期日期,按此调整即可.
2,以2个月为单位向前调整手机时间，直到找到可以安装软件的适合时间.
注意:调整时间跨度不要太大，因为不论时间是在证书有效期之前还是之后都会提示证书有问题!
最后装完软件再将时间调到正常即可
3,部分文件自签名后也可以解决过期问题。

诺基亚5800XM证书过期最新解决方法分享:


诺基亚5800XM证书过期最新解决方法分享
最近又看到了有些新人为诺基亚5800XM证书过期问题而烦恼，总结了前辈的经验，在以上的基础上加以改进，希望下面的帖子可以解决诺基亚5800XM证书过期的问题！
　拿到诺基亚5800XM后查看自己的手机产地码，看是什么地方的，记住，然后软格机：手机按*#7370#进行软格，软格密码12345；重启之后会出现英文，选择区域，就是你产地码所在地方，比如：如果机器为香港行货，择选择香港区域（HONG KONG），如果有马来新加坡的就在软格后选择singapore，马来西亚的就选择malasiya，然后日期调到当前，《现在好象可以硬格了。。》再安装就可以了，这时将时区调回也不会有影响了。也不排除再要调手机时间《有些软件》

我开始发觉我迷失了方向...

我最近发生了很多事........烦.....
喜怒哀乐就一起来找我了...........
我深信我还可以的，这是过渡期，会挨过去的
真的累了吗？是的。
下个星期要生日了。。。
今年我会不会过一个最不开心的生日呢。。。
让一切随风吧。。